株式会社パイロン

U-Boot 1.2.0-pylone5 (Oct 10 2007 - 22:41:30)

DRAM:  128 MB
Flash:  4 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
   Image Name:   Linux-2.6.26.8-pylone0
   Created:      2008-12-19   9:23:07 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1834472 Bytes =  1.7 MB
   Load Address: 30008000
   Entry Point:  30008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................................................................... done, booting the kernel.
s3c2440_timers_write: Bad register 0x40 value d8d208
Linux version 2.6.26.8-pylone0 (seiichi@se) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21pylone1)) #1 Fri Dec 19 18:23:04 JST 2008
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=00007177
Machine: Pylone Bishop
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C244X: core 399.651 MHz, memory 133.217 MHz, peripheral 66.608 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (2.116 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttySAC0,115200 console=tty0 preinit=/pylone root=/dev/mtdblock5 rootfstype=jffs2 console=ttySAC0,115200n8
irq: clearing subpending status 00000002
PID hash table entries: 512 (order: 9, 2048 bytes)
timer tcon=00500000, tcnt d8d2, tcfg 00000200,00000000, usec 0000170f
Console: colour dummy device 80x30
console [tty0] enabled
console [ttySAC0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126080KB available (3396K code, 255K data, 116K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 324 bytes
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
Pylone Bishop board PE-201A
wake enabled for irq 48
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c8800000, irq 33
DMA channel 1 at c8800040, irq 34
DMA channel 2 at c8800080, irq 35
DMA channel 3 at c88000c0, irq 36
S3C244X: Clock Support, DVS off
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 246
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
s3c2410 Backlight Driver Initialized.
Console: switching to colour frame buffer device 60x34
fb0: s3c2410fb frame buffer device
S3C2410/S3C2440 L3-interface successfully loaded.
s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
dm9000 Ethernet Driver, V1.30
eth0: dm9000 at c885e300,c8860304 IRQ 18 MAC: 00:1d:2d:ff:ff:ff (eeprom)
Driver 'sd' needs updating - please use bus_type methods
Pylone Bishop NOR flash device: 0x1000000 at 0x0
Creating 4 MTD partitions on "Bishop NOR flash":
0x00000000-0x00040000 : "U-Boot"
0x00040000-0x00330000 : "Kernel"
0x00330000-0x003f0000 : "initrd"
0x003f0000-0x00400000 : "U-Boot environment variables"
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=1, 7ns Twrph0=4 30ns, Twrph1=1 7ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
s3c2410_nand_update_chip: chip c7fcc2bc: 11
Scanning device for bad blocks
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x08000000 : "Root filesystem"
s3c2410-spi s3c2410-spi.0: No platform data supplied
s3c2410-spi: probe of s3c2410-spi.0 failed with error -2
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
s3c2410-ohci s3c2410-ohci: init err (00000000 0000)
ohci_hcd: can't start s3c24xx
s3c2410-ohci s3c2410-ohci: startup error -75
s3c2410-ohci s3c2410-ohci: USB bus 1 deregistered
s3c2410-ohci: probe of s3c2410-ohci failed with error -75
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
bishop-keypad: bishop keypad driver version 0.1
input: bishop Keypad as /class/input/input1
s3c2410 TouchScreen successfully loaded
input: s3c2410 TouchScreen as /class/input/input2
bishop-beeper: bishop beeper driver version 0.1
input: bishop beeper as /class/input/input3
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz).
s3c2440-sdi s3c2440-sdi: running at 261kHz (requested: 260kHz).
s3c2440-sdi s3c2440-sdi: running at 261kHz (requested: 260kHz).
s3c2440-sdi s3c2440-sdi: running at 261kHz (requested: 260kHz).
s3c2440-sdi s3c2440-sdi: powered down.
Registered led device: led4
Registered led device: led5
Registered led device: led6
Registered led device: led7
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.16.
ASoC version 0.13.2
uda1341: Audio Codec 0.1
asoc: UDA1341 <-> s3c24xx-i2s mapping ok
ALSA device list:
  #0: Bishop (UDA1341TS)
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
s3c2410-rtc s3c2410-rtc: setting system clock to 2008-12-21 10:02:49 UTC (1229853769)
Empty flash at 0x03af6064 ends at 0x03af6800
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 116K
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Activating swap...done.
Setting the system clock..
Cleaning up ifupdown....
Loading kernel modules...FATAL: Could not load /lib/modules/2.6.26.8-pylone0/modules.dep: No such file or directory
Loading device-mapper support.
Checking file systems...fsck 1.40-WIP (14-Nov-2006)
done.
Setting kernel variables...done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...Internet Systems Consortium DHCP Client V3.0.4
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

eth0: link up, 10Mbps, half-duplex, lpa 0x0400
Listening on LPF/eth0/00:1d:2d:ff:ff:ff
Sending on   LPF/eth0/00:1d:2d:ff:ff:ff
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPOFFER from 10.0.2.2
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 10.0.2.2
bound to 10.0.2.15 -- renewal in 33674 seconds.
done.
Setting console screen modes and fonts.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
* Not starting internet superserver: no services enabled.
Starting periodic command scheduler: crond.

Debian GNU/Linux 4.0 bishop ttySAC0

bishop login: